[an error occurred while processing this directive] Node:Slow compiler, Next:, Previous:Compiler performance, Up:Compiler performance

7.1 Slow Compilation

Q: Why GCC is compiling sooo slooowww?

A: That depends on what you mean by "slow". The following table gives "normal" gcc compilation speed, in source lines per second, on a 166-MHz Pentium:

Source language Without optimizations With -O2
C++ 800 400
C 1800 1000

Note that the numbers for compilation with -O2 are about 30% slower for GCC 2.95 and later versions than for previous versions. This is because GCC now does much more optimizations under -O2 than previous versions did.

As another data point, compiling the Allegro library takes about 3 minutes on a P500 and about 50 minutes on a 486/DX2-66.

On machines faster or slower than P166, scale these numbers accordingly. For example, 486/DX2-66 is about 4 times slower than P166. When comparing to this table, don't forget to count header files your program #includes in the total line count. And don't check compilation speed on very short programs (like the classic Hello, world!), because the overhead of loading the multiple passes of the compiler will completely hide the compiler performance. It is also useful to run the compilation twice in succession, especially if you have a disk cache installed, to prevent the overhead of the first load from skewing the results.

If your results are close to these (deviations of a few percent are considered "close" here), then that's as fast as you can get with GCC. If they are significantly slower, you may indeed have a problem; read on.

First, check to see if GCC pages to disk when it compiles. This is manifested by a heavy disk traffic which won't go away even if you have a large write-back disk cache installed. To be sure, disable the virtual memory services for your DPMI host (for CWSDPMI, load it before your program with the -s- switch, or use the CWSPARAM program to point the swap file to a non-existent drive), or use CWSDPR0 or PMODE/DJ as the DPMI host, and then run the compilation again; if the compiler aborts with an error message saying there isn't enough memory, then it was paging in your original environment.

If paging does happen, you need to free more extended memory. If you have a RAM disk, make it smaller, or don't use it at all (it only makes compiles run about 20% faster), or make your disk cache smaller (but don't discard the disk cache altogether); if you have other programs which use extended RAM, make them use less of it. Failing all of the above, buy more RAM (see the description of reasonable configuration). Also see recommendations for optimal software configuration.

If GCC doesn't page, check the settings of your disk cache. If you don't use a cache, install one--this can slash your compilation times by as much as 40%, more so when compiling a large number of small files. If you already have a cache, enable its delayed-write (a.k.a. write-back, a.k.a. staggered-write) operation. Some people disable the delayed-write feature for safety reasons, to avoid losing files due to system crashes. If you are worried about this, you can usually gain performance without sacrificing safety by enabling delayed-write together with an option that causes the cache to flush the write-behind data before the system returns to the DOS prompt. (For SmartDrv disk cache, this is achieved by specifying /N/F switches instead of /X.) GCC usually gains a lot when you set up your cache in such a way, because each compiler pass (pre-processor, compiler, assembler) must write temporary files that are used by the following passes.

It is also worthwhile to check the settings of your system BIOS. In particular, the following items should be checked against your motherboard vendor recommendations:

Internal and external CPU cache set to Enable
CPU cache scheme set to Write-back, if possible
DRAM and SRAM wait states vendor-recommended optimal values

Incorrect or suboptimal settings of the above items can explain as much as 30% performance degradation on 486 machines, and as much as 500% (!) if you have a Pentium CPU.


[an error occurred while processing this directive]